IPhone 3gs backlight fix, 6r8 coil replacement EBay seller id. tinner105

How to fix a iPhone 3G or 3Gs with water damage by Tech Life

           

Cost for this fix should be around

    

But as we see we not have all the parts yet.

And the cost is now just in parts 434 kr.

Or 106 nkr

Totally cost 540 kr i Norway.

But then you need to fix phone by yourself.

Then i wourld say, buy a new phone.

Create an iPod Video converter cable -- For Cheap!

Create an iPod Video converter cable -- For Cheap!

Of the various several portable devices that I regularly hook up to my TV using a standard 1/8th-inch to RCA cable, only the iPod uses a non-standard output configuration. It produces a video signal through what is normally the right audio channel. A few months ago on MacDevCenter, I wrote about connecting Video iPods to a television set by swapping around the RCA connectors. While this works perfectly well, it’s a pain to reach behind the set and switch connectors every time I want to watch iPod video on the TV. So I built a converter cable instead.
This article describes the parts I used and the steps I took to put together this cable. From beginning to end, the project took about twenty minutes to construct and test. It cost about $4. It’s slightly more if you count in the shipping and handling from parts supplier Mouser, even divided as it was among several projects. It’s less if you’ve got a spare USB cable lying around the house.
Want to build this yourself? Make sure you’re reasonably confident at wire-stripping and soldering. Those are really the only two skills involved.

Parts

Here are the parts you’ll need in order to get started:
4-Connector Plug, 4 Connector Jack. These two items carry the right and left audio, video and ground signals needed to output video from your iPod. The Mouser.com parts are 161-6435-EX (4-connector jack, $1.10) and 171-7435 (4-connector plug, $1.53). You’ll need one plug and one jack.
The four-connector plugs and jacks carry audio channels, video and ground.
Four-wire Cable (approx 4″-8″) You can usually find four-wired USB cables at your local dollar store although any 4-wire cable will work.
USB cable wire is cheap, ubiquitous and works great for this project.
You’ll also need: soldering equipment, a multimeter and a standard (not iPod compatible) 3-RCA-plug-to-3-banded-1/8th-inch A/V cable for testing.

Constructing The Wire

The following steps guide you through the process of connecting a jack and plug to your cable. Take time as suggested to test your connections with a multimeter to be sure you’ve put everything together properly

1. Disassemble the jack and plug. Unscrew the covers from the jack and the plug. To do this, hold onto either the metal plug or gray plastic portion of the jack and unscrew the black plastic cover.
2. Thread the covers onto the cable. The two covers are interchangeable, so you don’t have to worry about which end will be which. Make sure that the thinner part of the covers point towards the middle of the cable. If your cable is too thick for the covers, you may cut off the constrictive rear sections with scissors or a wire cutter. The finished cable looks a lot better when you don’t, so when sliding the covers onto the cable use a little thoughtful and cautious coercion.
3. Strip the wires. Use wire strippers to remove the outer covering from both ends of your cable. Then strip the ends of each individual wire.
All four wires really are there to the right; I just didn’t pull them apart. The unscrewed jack (left) and plug (right) are below, facing in their final directions.
4. Identify the jack connectors. The jack uses 4 connectors, three short rectangles in a row, and a larger upside-down-T-shaped connector behind them. From left to right, these three are left audio, ground, and video. The big connector is right audio. Test the connectors for yourself with your multimeter by plugging in a normal A/V cable to the jack and measuring resistance between each RCA plug and each connector.
The jack connectors.
5. Identify the plug connectors. The plug also uses 4 connectors, but with a different configuration. Figure 5 shows the plug using iPod terms. This is not the standard setup. A short connector hangs off to the left. This is ground. A small plug in the center contains two contact areas for the two audio channels, above and below the black line. The large upside-down-T-shaped connector carries video.
The plug connectors in iPod terms.
6. Solder the jack to the cable. Assuming you’re using USB wire coloring:
   • Connect the white wire to the left audio connector.
   • Connect the black wire to ground.
   • Connect the green wire to the video connector.
   • Connect the red wire to the large right audio connector.
7. Test your connections. Plug in your normal A/V cable and confirm that the white wire connects to the white RCA plug, the red to the red, the green to the yellow and the black to the ground (the large circular part that surrounds each plug). If you’ve misconnected, go back and resolder as needed.
Test your jack’s wiring before starting work on the plug.
8. Cover the jack. Carefully but firmly, shift the black cover off the cable and screw it back onto the jack.
9. Solder the plug to the cable. Again, assuming USB wire colors:
   • Connect the black wire to ground.
   • Connect the green wire to the large video connector.
   • Connect the white and red wires to the two audio connectors, one wire per connector. (This is the trickiest part, as the two connectors are so small and close together.)
10. Attach the plug cover. As you did with the jack, shift the black cover off the wire and screw it onto the plug. That’s it. You’re finished and ready to test.
The final product should look clean and professional
11. Test. Connect your A/V cable to your television with the RCA plugs in their normal and usual configuration: yellow plugged into yellow, red into red and white into white. Connect the 1/8th-inch plug end of the A/V cable to the jack in your new converter cable and plug the cable into your iPod. Play a video out to your television. The audio and sound should match the quality you experience directly from your iPod.

If you connect a lot of gadgets up to your TV, this simple cable cuts out a lot of annoying overhead. Use this adapter instead of reconfiguring your TV every time you watch iPod video. If you can strip wires and solder, you can easily build this project: it won’t cost a bundle and it won’t take a lot of your time.

How to build a custom iPod or iPhone cable

http://revision3.com/systm/ipodcables

How to make an Ipod charger while playing audio out.
See video on link above.

Below  is an unit that make this an easy task. Link to buy it is shown in the video.

To make an audio out:

Audio out is: pin 2 = Ground
                      pin 3 = Left channel
                      Pin 4 = Right channel
The wire you connect ground for left and right together.